English French German Italian Portuguese Russian Spanish

A Vintage Vehicle for a Veteran

or Yank Tank for a Gent of some Rank

by Charles Hand

HM-HG3416_01_lrg.jpgMy wife recalls relative sending her a plaque of his unit insignia while he was serving with Gen. George Patton's Panthers or Tank Destroyers. Years later, he retired as Lieut. Col. A color copy of the insignia, plus color profiles and photos of the armored fighting vehicles use by that unit are in reference one. Those prompted me to attempt a bottled model of such a vehicle as a surprise birthday gift for the relative.

The M-10, with a 3 inch gun (76 mm, compared to 37 mm guns on the Sherman tanks) seemed a good choice. It’s the first fully-tracked tank developed by the U.S. to combat enemy tanks and was relatively successful. Reference 1 lacked dimensions, so I estimated those as 8 foot wide by 20 foot long by 9 foot high and I did a sketch at 1:96 (1/8 inch = 1 foot) to suit a rectangular or Roddenbery’s 19 ounce (562 ml) cane syrup bottle.

The following photos shows initial rough shaping of paired pine blocks to form the hull and another pine block for the turret and gun – each joined by 1/16 inch diameter styrene rods and set upon temporary wood tracks. A thin sheet of wood was shaped to form an inner base – with indentations for the treads – and split into three pieces.

7-13-2012 10-45-07 AM.jpg Tank 03.jpg

A thin wire simulates a towing cable and bent wires in drilled holes the lifting lugs. Most details were fashioned from styrene rods, tubes, strips and sheets. Track portions were built up of styrene parts and include treads of strips cut from v-grooved sheets. The whip antenna is a paintbrush bristle.

7-13-2012 10-45-54 AM.jpg

Liquid cement fastened the styrene items; white glue joined the styrene to wood and wood components. Gesso was applied to joints to minimize gaps. Flat Floquil paints were used: “earth” on the Inter base, “primer gray” on guns, “railroad brown” on tank surfaces, “white” stars, “silver” lights and “black” tow cables.

7-13-2012 10-46-14 AM.jpg 7-13-2012 10-46-49 AM.jpg 7-13-2012 10-46-35 AM.jpg

Sequence was:

1.       3 Inter base pieces,

2.       Joining hull halves,

3.       Upper grille,

4.       Washer under turret,

5.       Turret,

6.       5 bedrolls on turret sides,

7.       2 machine guns atop turret,

8.       Track assemblies,

9.       Whip antenna.

Glue was then applied to the base depressions and the model shifted and pressed into place. The unit logo was affixed on the bottle cap and also on a label on the underside.

The model involved 50 hours of effort over a period of four weeks.

After the model was well underway, I chanced upon references two and three which disclosed my estimated dimensions were in error and should of been 10 foot wide by 19 feet 7 inches long by 8 feet 1 1/2inches high (3.o5 x 5.97 x 2.82 m).  These also related to a U.K. version which had a net 17-pounder gun and was named the Achilles.

Reference 1: "U.S. Tank Destroyers in Combat 1941 – 1945" by Stephen J. Zaloga. Concord Publications Company, 1996.

Reference 2: "Tanks and Other Armored Fighting Vehicles 1942 – 1945" by B.T. White, McMillan Publishing Company, 1976.

Reference 3: "The Illustrated Encyclopedia of 20th Century Weapons and Welfare" Purnell and Sons Limited, 1967/1969.

915a.jpg 915c.jpg

 

 

 

New Bottles

Bottle 1418 - Eagle, Sun, Moon Totem in a Bottle
Bottle 1417 - Barca a Pale in a Bottle

New Articles

 Only 5 most recent Bottles/Articles displayed.  Click on "New Items" in the menu above for all new site content.